Tag: aarch64

Posted on by — Leave a comment

install Fedora on a Raspberry Pi 3

Fire up a Raspberry Pi with Fedora.

The Raspberry Pi Foundation has produced quite a few models over the years. This procedure was tested on third generation Pis – a Model B v1.2, and a Model B+ (the older 2 and the new 4 weren’t tested). These are the credit-card size Pis that have been around a few years.

get hardware

You do need a few hardware items, including the Pi. You don’t need any HaT (Hardware Attached on Top) boards or USB antennas. If you have used your Pi in the past, you probably have all these items.

  • current network. Perhaps this is your home lab.
  • ethernet cable. This connects the current network to the Raspberry Pi
  • Raspberry Pi 3, model B or B+.
  • power supply
  • micro-SD card, 8GB or larger.
  • keyboard and video monitor.

The keyboard and video monitor together make up the local console. It’s possible – though complicated – to get by without a console, such as setting up an automated install then connecting over the network. A local console makes it easy to answer the configuration questions during Fedora’s first boot. Also, a mistake during AP configuration may break the network, locking out remote users.

download Fedora Minimal

The Fedora Minimal image, one of Fedora’s alt downloads, has all the core packages and network packages required (well, nearly – check out dnsmasq below). The image contains a ready-made file system, with over 400 packages already installed. This minimal image does not include popular packages like a development environment, Internet service or desktop. These types of software aren’t required for this work, and may well use too much memory if you install them.

The Fedora Minimal raw image fits on a small SD card and runs in less than 1 GB of memory (these old Pis have 1GB RAM).

The name of the downloaded file is something like Fedora-Minimal-32-1.6.aarch64.raw.xz. The file is compressed and is about 700MB in size. When the file is uncompressed, it’s 5GB. It’s an ext4 file system that’s mostly empty – about 1GB is used and 4GB is empty. All that empty space is the reason the compressed download is so much smaller than the uncompressed raw image.

copy to the micro-SD card

  • Copy the image to a micro-SD card.

This can be a more complex than it sounds, and a painful experience. Finding a good micro-SD card takes work. Then there’s the challenge of physically attaching the card to your computer.Perhaps your laptop has a full SD card slot and you need a card adapter, or perhaps you need a USB adapter. Then, when it comes to copying, the OS may either help or get in your way. You may have luck with Fedora Media Writer, or with these Linux commands.

unxz ./Fedora-Minimal-32-1.6.aarch64.raw.xz
dd if=./Fedora-Minimal-32-1.6.aarch64.raw of=/dev/mmcblk0 bs=8M status=progress oflag=direct

set up Fedora

  • Connect the Pi, power cable, network cable and micro-SD card.
  • Hit the power.
  • See the colored box as the graphics chip powers up.
  • Wait for the anaconda installer to start.
  • Answer anaconda’s setup questions.

Initial configuration of the OS takes a few minutes – a couple minutes waiting for boot-up, and a couple to fill out the spokes of anaconda’s text-based installer. In the examples below, the user is named nick and is an administrator (a member of the wheel group).

Congratulations! Your Fedora Pi is up and operational.

update software

  • Update packages with `dnf update`.
  • Reboot the machine with `systemctl reboot`.

Over the years, a lot of people have put a lot of work into making the Raspberry Pi devices work. Use the latest software to make sure you get the benefit of their hard work. If you skip this step, you may find some things just don’t work.

The update downloads and installs about a hundred packages. Since the storage is a micro-SD card, writing new software is a slow process. This is what using computing storage felt like in the 1990s.

things to play with

There are a few other things that can be set up at this point, if you want to play around. It’s all optional. Try things like this.

  • Replace the localhost hostname with the command `sudo hostnamectl set-hostname raspi`.
  • Find the IP address with `ip addr`.
  • Try an SSH login, or even set up key-based login with `ssh-copy-id`.
  • Power down with `systemctl poweroff`.
Posted on by — Leave a comment

Fedora 29 on ARM on AWS

This week Amazon announced their new A1 arm64 EC2 Instances powered by their arm64 based Graviton Processors and, with a minor delay, the shiny new Fedora 29 for aarch64 (arm64) is now available to run there too!

Details on getting running on AWS is in this good article on using AWS tools on Fedora article and over all using Fedora on the AWS arm64 EC2 is the same as x86_64.

So while a new architecture on AWS is very exciting it’s at the same time old and boring! You’ll get the same versions of kernel, same features like SELinux and the same versions of the toolchain stacks, like the latest gcc, golang, rust etc in Fedora 29 just like all other architectures. You’ll also get all the usual container tools like podman, buildah, skopeo and kubernetes, and orchestration tools like ansible. Basically if you’re using Fedora on AWS you should be able use it in the same way on arm64.

Getting started

The initial launch of A1 aarch64 instances are available in the following four regions: US East (N. Virginia), US East (Ohio), US West (Oregon), Europe (Ireland). Direct links to launch the Fedora aarch64 AMIs directly are available here on the Fedora Cloud site.

Getting help

The Fedora support for aarch64 is very robust. It’s been widely used and tested across a number of platforms but of course with new users and new use cases will pick up issues that we’ve yet to encounter. So what is the best way to get help? If you’re having a crash in a particular application it should be reported in the usual way through RH Bugzilla, we have an ARMTracker tracker alias to block against to help identify Arm issues. For assistance with Arm specific queries and issues the Fedora Arm mailing list and we have the #fedora-arm IRC channel on Freenode.

Known issues

We have one known issue. The instance takes a while to get started, it can be up to 5 minutes. This is due to entropy and has been a general problem in virtual environments, across all architectures. We’re working to speed this up and it should be fixed soon. Once things are up an running though everything runs as expected.

Upcoming features

There will be Fedora 29 Atomic host coming in the next Two Week Atomic release, we unfortunately missed their release this time by a small window but it’ll be available in about 2 weeks with their next release and will appear on the site once released. We can’t let you have all the fun at once 😉